You may NOT reverse engineer, develop, decompile, translate, adapt or dissemble the Software, not shall you attempt to create the source code from the object code of the Software.
You may not transmit the Software over any network or between any devices. No Warranty and Limitations on Liability: a. In order to provide you with this free service, Licensor is unable to offer or provide any warranty or make any representation about any benefit or opportunity which you may obtain from Software or Documentation.
Should the Software not perform in accordance with any expectation you may have, your exclusive remedy, and Licensor's sole obligation under this warranty shall be, at Licensor's sole discretion, correction of the defect or, in the case of purchase of the product with which Software is operated, refund of the purchase price paid for such product.
Any use by you of the Software is at your risk. This limited warranty is the only warranty provided by Licensor regarding the Software and, except for this limited warranty, the Software and the Documentation is provided "AS IS. Licensor does not warrant that the functions contained in the Software will meet any requirements or needs you may have, or that the Software will operate error free, or in an uninterrupted manner, or that any defects or errors in the Software will be corrected, or that the Software is compatible with any particular platform.
Firewire Ports that are built-in to the Motherboard. You will need to make sure this is set to Enable or ON. Some software only allow you to work with footage that comes from an SD card or from the Hard Drive. We use Vegas Pro and Vegas Movie Studio and both of those software packages support capturing video through the Firewire port.
Make sure what ever video capture program you are using, that you turn off the Device Control in the video capture program. If it is not turned off, you may run into problems trying to capture the video footage. Depending the the software you may also need a special driver for the audio software, in addition to the Firewire Driver. Farther down in the article, under Step 13, I show you have to check to see if the Device Manage will see the connected audio device.
Using a Firewire connection with a Photo an Slide Scanners If you have a scanner, such as a Nikon scanner, you may find it will not work with Windows 10, even if you have a built-in Firewire port or a Firewire expansion card.
The problem here is the scanner driver or software will not work under Windows Download the demo version of the software and try it out. This have solved problems for people using Canon, Nikon and a host of other scanners that are connected through the Firewire port. Don't worry if the scanner doesn't show up in the Device Manager, as long as the device manager sees the Firewire card, the above scanner software should find it.
NOTE: I have heard from a lot of people having problems when trying to use a Firewire card with a TI chipset with their scanner, even the the scanning software. As soon as they switched to a Firewire card with the VIA chipset, like the ones I have shown you above, they had no more problems. Mouse Clicks In this article, when we say to Click or Left Click , you will use the Left mouse button, as shown below.
When we say Right Click , you want to click the Right mouse button, as shown below. Here we will show you step by step instructions, along with screen shots on downloading, installing and setting up the Firewire Drives. For Windows 7 users, please skip down to the section titled "The Fix for Windows 7". However, Microsoft left out the Legacy Firewire driver version. Please follow these steps below exactly as they are written.
In fact, you might want to read through them first, the go back and follow each step. I have provided screen shots for each step. If you are running Windows 8, the steps are exactly the same for Windows Then once you have downloaded the installer, follow the instructions below.
Find where you downloaded the file to. NOTE: It will only take a second or two to install and it may not show you any messages when it is done installing. This will install the Firewire Legacy Drivers. NOTE: It will only take a second or two to install and then it returns you to the folder with no message that it has installed. But, don't worry it has installed. If you don't see the file extensions above, such as. Just click on the View tab and check the box that says File name extensions, as shown below.
Look for the line that says IEEE host controller. Save the BIOS settings and reboot the computer. You will need to purchase a Firewire Expansion Card that plugs into one of the slots on the motherboard. Make sure you power off the computer before moving the Firewire card to another expansion slot. Now see if it shows up in the Device Manager. If it still does not show up, make sure the Firewire has the VIA chipset.
Sometimes Firewire cards that have the TI chipset will not be seen in the Device Manger and you will not be able to use it. Try purchasing another Firewire card with the VIA chipset and see if it works.
Below is a sample of what the Device Manager will show. Step 8 Then select Browse my computer for driver software. As shown below. Step 9 Select Let me pick from a list of available drivers on my computer as shown below.
Then click on Next. Step 10 A list of drivers will be shown. Step 11 Now you should see the screen below, saying Windows has successfully updated your drivers. Step 13 Connecting different Firewire device to your computer and verifying the connection with Device Manager. I have three different examples below, depending on the type of device your are connecting to the Firewire port.
Also a flat bed scanner, slide or photo scanner Connect the Camcorder, MiniDV deck or scanner to the Firewire port using a Firewire cable. Once you are connected, power on the device.
Go back into the Device Manager. Asked 12 years, 3 months ago. Active 12 years, 1 month ago. Viewed times. Improve this question. Add a comment. Active Oldest Votes. Improve this answer. You may wish to be cautious about changing kernel specific stuff and just wait until Sign up or log in Sign up using Google. Sign up using Facebook. Sign up using Email and Password. Post as a guest Name. Email Required, but never shown.
0コメント