Lost Frames: Number of frames lost. Page Block Blocks Retransmitted: Number of blocks retransmitted over the wireless interface. Blocks Discarded: Number of blocks discarded could not be sent over the wireless. Controls Refresh: Click Refresh to update the statistics display. Packets Received: Number of Ethernet packets received over the wireless interface.
Page Operating Notes Ethernet port on the sector controller and subscriber stations. Use the following steps to create a simple pass-through configuration suitable for initial system testing of a version 3. This includes information for site planning, installation, antenna alignment, and basic configuration. Page 68 7. Click the Apply button to create the connection. Repeat steps 1 through 7 for each subscriber station to be included in the group. The system should now pass all tagged and non-tagged traffic.
Figure Op. Notes - Tagged Management Configuration Over-the-air management is possible only after a group and connections are configured to transport the VLAN management traffic. Page Table Diag. While writing the new software into terminal flash memory an unexpected error occurred. Try to repeat the process and if the error persists contact your local representative. Try configuration! If the problem persists, contact customer support.
Page Disable Tagged Management 2. Perform a long-reset on the system by depressing the reset button for longer than five seconds. This also resets some other operating parameters. See section 5. Page Replacing System Fuse Be certain to use fuses of the same type and rating.
Note space Figure 32 : Diag. Replace the fuse holder in the system terminal and secure. Restore power to the system.
Page 80 ANe user manual Table 29 : Spec. Page Dc Power Supply Cable Connections Note: DC units are not equipped with power switches and activate immediately when connected to a power source. Note: The Widemouth power supply options are not available for the AN Antenna Gain Applies to sectorized antennas only.
Table 33 : Spec. Page Cli Interface Table 35 : Spec. RS column is RS circuit name. Page Connecting Via Telnet The following commands are available via Telnet and Console connections to the terminal. To make settings permanent, use the 'save' command. Page Glossary Of Terms A theoretic construct of an antenna that radiates its signal degrees both vertically and horizontally—a perfect sphere. Generally used as a reference.
Inter-exchange Carrier. A long-distance phone company. Local Exchange Carriers. The traditional local wired phone company. Local access though the Ethernet port is not affected. Print page 1 Print document pages. Rename the bookmark. Delete bookmark? Cancel Delete. Click the Apply button to save and activate these settings. Repeat steps 1 - 6 for each subscriber station. Click New Group to display the Group Configuration screen. Enter a unique name for this group in the Group Name field. Set the Group QoS value for sending multicasts i.
Previous Page. Next Page. Use the default values for all other fields. Page 2 GUI over the wireless interface. Access is available though the subscriber station Ethernet port. The information in this document is subject to change without notice. Figure Weatherproofing Procedures - Part 3 4.
Work the mastic putty well into the area between the connector and the body of the radio. The cable quality and loss profile has a critical bearing on the performance of the wireless link. If the customer selects to purchase the cable separately, the cable must be of a recommended type and be assembled using the recommended connectors. The tower ground and the building ground should be connected together.
Page Idu Installation This section of the manual presents a basic overview of the steps required to install the terminal, outdoor transceiver, antenna, and associated equipment.
Do not rely on the removable power or signal cables to provide system grounding. It is necessary to attach the IF cable before aiming the antenna. This method allows the operator to use a common Web browser to access and control the terminal.
Microsoft Internet Explorer is recommended for its support of context-sensitive help. The saved settings will be preserved through system reset and power-cycles. Page Slave System Settings All settings will become effective immediately.
A misaligned antenna will decrease the receive signal and can even result in a total loss of the RF signal. The antennas and ODUs must be mounted and the IDU installed and configured before the antenna alignment can be completed. Use of either the audible buzzer or voltage alignment pin is enabled using the software interface. A faster the repetition rate of the buzzer indicates a stronger the signal being received from the remote-end transmitter. The Redline radio can be used as a tool to determine whether interference is present on any of the prescribed channels.
All rights reserved. The information in this document is subject to change without notice. The statements, configurations, technical data, and recommendations in this document are believed to be accurate and reliable, but are presented without express or implied warranty.
0コメント